AEG MODICON AS-P892-000输入输出模块
1.产 品 资 料 介 绍：
- 多通道混合设计，集成数字量输入 / 输出双功能，无需拆分配置，适配复合型控制场景。
- 输入通道支持干 / 湿接点自由切换，兼容无源传感器与有源信号，现场接线灵活无限制。
- 输出通道采用继电器触点设计，单路承载电流达 5A，可直接驱动小型电机、电磁阀等大功率负载。
- 与 Modicon 984 系列控制器原生兼容，背板总线直连无需转接，老旧系统升级零适配成本。
- 内置 1500Vrms 信号隔离电路，输入 / 输出 / 电源三者互相隔离，抗电磁干扰能力行业领先。
- 工作温度覆盖 - 20℃~70℃宽温范围，湿度耐受 5%~95% 不结露，极端工况稳定运行。
- 通道响应时间＜10ms，高频次信号采集与指令输出无延迟，适配高速启停控制需求。
- 35mm DIN 标准导轨安装，卡扣式快速固定，单人即可完成拆装，维护效率提升 50%。
- 电源反接保护 + 过流熔断双重防护，避免接线错误或负载异常导致模块永久性损坏。
- 支持模块级地址拨码设置，无需软件配置，即插即用，缩短系统调试周期。
- 状态指示灯采用双色设计，电源 / 通信 / 通道故障分色显示，故障定位精准到单路。
- 兼容 Modbus RTU 通信协议，可通过上位机远程监控通道状态，实现集中化运维管理。
- 窄体结构设计仅占 3 个安装位，在高密度控制柜中可紧凑布局，空间利用率提升 30%。
- 作为 984 系列存量系统核心备件，替换旧款 I/O 模块无需改动程序，停机更换时间＜15 分钟。
- 适配机床控制、流水线联动、仓储设备、暖通空调等多场景，通用性与可靠性兼具。
AEG MODICON AS-P892-000输入输出模块 英文资料：
Multi channel hybrid design, integrated digital input/output dual function, no need for split configuration, suitable for composite control scenarios.
The input channel supports free switching between dry/wet contacts, compatible with passive sensors and active signals, and has flexible and unrestricted on-site wiring.
The output channel adopts a relay contact design, with a single current carrying capacity of 5A, which can directly drive high-power loads such as small motors and solenoid valves.
Native compatibility with Modicon 984 series controllers, direct connection of backplane bus without adapter, zero adaptation cost for upgrading old systems.
Equipped with a built-in 1500Vrms signal isolation circuit, the input/output/power supply are isolated from each other, and the anti electromagnetic interference capability is industry-leading.
The working temperature covers a wide temperature range of -20 ℃~70 ℃, with a humidity tolerance of 5%~95% without condensation, and stable operation under extreme working conditions.
Channel response time<10ms, high-frequency signal acquisition and command output without delay, suitable for high-speed start stop control requirements.
35mm DIN standard rail installation, snap on quick fix, single person can complete disassembly and assembly, maintenance efficiency increased by 50%.
Dual protection of power reverse connection and overcurrent fuse to avoid permanent damage to the module caused by wiring errors or abnormal load.
Support module level address dialing settings, no software configuration required, plug and play, shorten system debugging cycle.
The status indicator light adopts a dual color design, with power/communication/channel fault color separation display, and accurate fault location to a single channel.
Compatible with Modbus RTU communication protocol, it can remotely monitor channel status through the upper computer and achieve centralized operation and maintenance management.
The narrow structure design only occupies 3 installation positions, allowing for compact layout in high-density control cabinets and increasing space utilization by 30%.
As a core spare part of the 984 series existing system, replacing the old I/O module does not require any program changes, and the downtime for replacement is less than 15 minutes.
Adapt to multiple scenarios such as machine tool control, assembly line linkage, storage equipment, HVAC, etc., with both universality and reliability.
AEG MODICON AS-P892-000输入输出模块 产品展示
产品视频
3.其他产品
Prosoft 5304-MBP-PDPM控制器模块
B&R 5AP933.215C-00触摸屏
BENTLY 3500/33 149992-01控制卡背板
4.其他英文产品
BENTLY 3500/22M Interface module
TRICONEX AO3481 Output module
HIMA K9202 Fan components
| IS220PCAAH1A IS220PCAAH1B | SERVOSTAR-341 | IEPEP03 |
| IS220PAOCHIA IS220PAOCH1B | S5001 | BUS MONITOR |
| IS220PAICH2A IS220PAICH2B | 52010-00 | IMDSI02 |
| IS220PAICH1A IS220PAICH1B | SS2000PCI-2 | IMSET01 |
| IS215UCVGH1A | HA42A6-R233 | IMDS001 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
