1.产 品 资 料 介 绍：
- 安装 ABB ACS401002032 需选用 35mm 标准导轨，固定扭矩 120-150N・cm，确保安装面平整无振动。
- 接线前确认输入电压与 ACS401002032 额定 3 相规格匹配，避免超压损坏内部功率模块。
- 该型号支持 V/F 与矢量控制模式，需按负载类型（风机 / 泵 / 机械负载）通过面板配置参数。
- 主回路电缆选用≥2.5mm² 铜导线，信号电缆单独屏蔽布线，减少电磁干扰保障运行稳定。
- 定期用干燥毛刷清洁 ACS401002032 散热风道，IP21 防护需防范灰尘堵塞影响散热。
- 运行环境温度控制在 0℃至 + 40℃，超温需按 1.5%/℃降容使用，避免过热报警停机。
- 启动 ABB ACS401002032 前需检查参数备份完整性，重点确认过载保护与过流阈值设定。
- 接线端子紧固时使用力矩扳手，M4 螺丝按 1.2N・m 扭矩操作，防止接触不良发热。
- 每 12 个月检测主回路绝缘电阻≥10MΩ，同时检查冷却风扇运行状态，2-3 年更换一次风扇。
- 闲置超 6 个月重启前，先通电放电 30 分钟，空载试运行无异常后再逐步加载至额定负载。
ACS401002032逆变器 英文资料：
Installation of ABB ACSS401002032 requires the use of 35mm standard guide rails with a fixed torque of 120-150N · cm to ensure a flat and vibration free installation surface.
Before wiring, confirm that the input voltage matches the rated 3-phase specification of ACSS401002032 to avoid overvoltage damage to the internal power module.
This model supports V/F and vector control modes, and parameters need to be configured through the panel according to the load type (fan/pump/mechanical load).
The main circuit cable uses ≥ 2.5mm ² copper wire, and the signal cable is separately shielded and wired to reduce electromagnetic interference and ensure stable operation.
Regularly clean the ACSS401002032 heat dissipation duct with a dry brush, and IP21 protection should prevent dust from blocking and affecting heat dissipation.
The operating environment temperature should be controlled between 0 ℃ and+40 ℃. If the temperature exceeds the limit, the capacity should be reduced by 1.5%/℃ to avoid overheating alarm and shutdown.
Before starting ABB ACSS401002032, it is necessary to check the integrity of parameter backup, with a focus on confirming overload protection and overcurrent threshold settings.
When tightening the wiring terminals, use a torque wrench and apply a torque of 1.2N · m to M4 screws to prevent poor contact and heat generation.
Every 12 months, the insulation resistance of the main circuit should be checked to be ≥ 10M Ω, and the operating status of the cooling fan should be checked. The fan should be replaced every 2-3 years.
Before restarting after being idle for more than 6 months, power on and discharge for 30 minutes. After a no-load trial run with no abnormalities, gradually load to the rated load.
Summary: The stable operation core of ABB ACSS401002032 inverter lies in standardized installation, parameter adaptation, heat dissipation guarantee, and regular maintenance. With flexible control modes and complete protection functions, it can adapt to power drive scenarios in industry. Combined with compliant operation, it can fully leverage its high reliability and energy-saving advantages, ensuring continuous and stable operation of the equipment.
ACS401002032逆变器 产品展示
产品视频
3.其他产品
ABB CI546 3BSE012545R1控制模块
Emerson 1C31222G01控制模块
Honeywell 8C-PCNT02 51454363-275监测模块
4.其他英文产品
MTL 8939-HN Counting module
PPD512A10-150000 controller
PROSOFT PLX32-EIP-SIE Communication gateway module
| 745-W2-P5-G5-HI-A-R-E | 8030-RIM-361 | 6AV35151MA201AA0 |
| 745-W2-P5-G5-HI-AR | 8030-RIM-123 | 710-609995-002 |
| 745-W2-P5-G5-HI-A-L-R-E | 8030-RIM-121 | X-AI 32 02 |
| 745-W2-P5-G5-HI-A-E-H | 8030-RIM-101 | X-FTA 009 02L |
| 745-W2-P5-G5-HI-A-E | 8030-R1M-185A | X-FTA 008 02L |
| 745-W2-P5-G5-HI-A | 8030-PV-28 | X-FTA 007 02L |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
