1.产 品 资 料 介 绍：
- 专为 TEL ACT12 系列设备配套，伺服轴控信号匹配度高
- 多路独立数字输入通道，精准采集限位、原点感应信号
- 多路高速数字输出端口，直连安川伺服驱动器控制轴体
- 工业级金手指插槽，插拔稳定，长期使用不易接触不良
- 内置信号滤波电路，隔绝机台高频电磁干扰
- 板载故障状态指示灯，快速定位通道断线、短路故障
- 集成硬件过流、过压保护，避免伺服冲击损坏板卡
- 实时同步轴位反馈数据，保障多轴联动运动精度
- 板载存储芯片，断电保留轴控参数无需重复调试
- 标准工控板尺寸，直接装入设备卡槽无需改造机柜
- 低延迟信号传输，缩短伺服响应滞后时间
- 耐腐蚀 PCB 基材，适配半导体洁净车间工况
- 通道独立隔离设计，单路故障不影响其余信号回路
- 支持设备总线通讯，可对接上位机统一监控 I/O 状态
- 出厂校准信号阈值，上机即可投入量产工艺TEL AP9E-0318C-12 输入输出模块是半导体设备多轴运动控制核心板卡，保障产线连续稳定生产。
TEL AP9E-0318C-12输入输出模块 产品英文
TEL AP9E-0318C-12 is a servo I/O board specifically designed for ACT12 semiconductor machines, dedicated to axis control signal acquisition and drive output, and suitable for etching thin film equipment.
Specially designed for TEL ACT12 series equipment, with high matching of servo axis control signals
Multiple independent digital input channels for precise acquisition of limit and origin sensing signals
Multiple high-speed digital output ports, directly connected to Yaskawa servo drive control shaft body
Industrial grade gold finger slot, stable insertion and removal, not prone to poor contact during long-term use
Built in signal filtering circuit to isolate high-frequency electromagnetic interference from the machine
Onboard fault status indicator light, quickly locate channel disconnection or short circuit faults
Integrated hardware overcurrent and overvoltage protection to prevent servo impact damage to the board
Real time synchronized axis feedback data to ensure the accuracy of multi axis linkage motion
Onboard storage chip, retains axis control parameters without the need for repeated debugging when powered off
Standard industrial control board size, can be directly inserted into the equipment card slot without the need to modify the cabinet
Low latency signal transmission, shortening servo response lag time
Corrosion resistant PCB substrate, suitable for semiconductor cleanroom conditions
Channel independent isolation design, single channel failure does not affect other signal circuits
Supports device bus communication and can be connected to the upper computer for unified monitoring of I/O status
Factory calibrated signal threshold, ready for mass production on the machine
TEL AP9E-0318C-12 input/output module is a semiconductor equipment multi axis motion control core board, ensuring continuous and stable production on the production line.
TEL AP9E-0318C-12输入输出模块 产品展示
视频展示
中文产品
Bently 1900-65A监测模块
A-B 1398-DDM-075数字伺服驱动器
HIMA F8621A安全控制模块
LAND M2300/1100C-V pyrometer
EPRO MMS6220 The front sensor
TRICONEX PI3381 Industrial control card a
| 6ES5374-2KL21 | CACR-SR44BY1SD-Y48 | 6DD2920-0XG02 |
| 6ES5374-2FP22 | CACR-SR20TB5BM | 6ES5314-3UA11 |
| 6ES5374-2AL21 | 6SC9111-2AJ45 | 1BF41-0BC0 |
| 6ES5374-2AH21 | CACR-SR30SZ1SD-Y38 | 6DD2920-0XD01 |
| 6ES5374-1KJ11 | 6SC6100-7VA01 | 6DD2920-0XC03 |
| 6ES5374-0AA11 | 6SC6110-0GB00 | 6ES5312-5AA31 |
| 6ES5373-1AA41 | CACR-SR10BB1AM | 6DD2920-0XC02 |
| 6ES5372-1AA61 | 6SC9121-5CD15 | 6ES308-3UC11 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
