00-291-556机器人示教器 

1.产 品 资 料 介 绍：

00-291-556 机器人示教器使用注意事项

1. 操作示教器前取下手上金属饰品，避免触碰端子造成短路，同时防止划伤外壳与屏幕。
2. 手持示教器时抓握防滑区域，避免单手甩动或高空跌落，防止内部电路板焊点脱落。
3. 连接示教器电缆时对准接口卡扣，轻推到位后锁紧，严禁暴力插拔导致接口针脚弯曲。
4. 检查电缆无破损、断线情况，走线时避开机器人运动轨迹，防止被夹断或碾压。
5. 示教器开机前确认机器人处于 “手动模式”，急停按钮处于弹出状态，避免误触发自动运行。
6. 触摸屏幕时使用指腹轻触，禁止用指甲、螺丝刀等尖锐物体按压，防止屏幕碎裂或触控失灵。
7. 编程或修改参数时，每完成一步操作及时保存，避免断电导致程序或参数丢失。
8. 调试机器人运动时，先将速度调至低速档，确认运动方向无误后再逐步提升速度。
9. 示教器使用环境需保持干燥，避免在潮湿、多尘、油污场所使用，防止液体或粉尘进入内部。
10. 严禁在示教器上堆放重物，避免阳光直射屏幕，防止屏幕老化或出现残影。
11. 操作过程中若出现屏幕闪烁、按键无响应等异常，立即按下急停按钮并断电检查。
12. 清洁示教器时先断开电源，用沾有少量清水的软布擦拭外壳，屏幕需用专用屏幕清洁剂。
13. 电池电量低时及时充电，避免过度放电影响电池寿命；长期不使用时，需每月充电一次。
14. 禁止私自拆卸示教器外壳，内部精密电路和传感器非专业人员维修易造成二次损坏。
15. 存放示教器时需放入专用防护箱，置于通风干燥处，避免与腐蚀性化学品混放。

00-291-556机器人示教器 英文资料：

Precautions for using the 00-291-556 robot teaching pendant

Before operating the teaching pendant, remove the metal jewelry from your hands to avoid touching the terminals and causing a short circuit, while also preventing scratches on the casing and screen.

When holding the teaching pendant, grip the anti slip area to avoid swinging with one hand or falling from a height, and prevent the internal circuit board solder joints from falling off.

When connecting the teaching pendant cable, align it with the interface buckle, gently push it into place, and then lock it. It is strictly prohibited to forcefully plug or unplug to cause the interface pins to bend.

Check the cables for any damage or breakage, and avoid the robot's movement trajectory during wiring to prevent them from being pinched or crushed.

Before turning on the teaching pendant, confirm that the robot is in "manual mode" and the emergency stop button is in the pop-up state to avoid triggering automatic operation by mistake.

When touching the screen, use fingertips to lightly touch it. Do not press with sharp objects such as nails or screwdrivers to prevent the screen from shattering or touch failure.

When programming or modifying parameters, save each completed step in a timely manner to avoid losing the program or parameters due to power failure.

When debugging the robot's motion, first adjust the speed to low gear, confirm that the direction of motion is correct, and then gradually increase the speed.

The teaching pendant should be used in a dry environment, avoiding use in damp, dusty, and oily places to prevent liquids or dust from entering the interior.

It is strictly prohibited to stack heavy objects on the teaching pendant, avoid direct sunlight on the screen, and prevent screen aging or residual images.

If there are any abnormalities such as screen flickering or unresponsive buttons during operation, immediately press the emergency stop button and turn off the power for inspection.

When cleaning the teaching pendant, first disconnect the power supply, wipe the outer shell with a soft cloth dipped in a small amount of water, and use a specialized screen cleaner for the screen.

Charge the battery in a timely manner when the battery level is low to avoid excessive discharge affecting the battery life; When not in use for a long time, it needs to be charged once a month.

It is prohibited to dismantle the outer shell of the teaching pendant without authorization. Non professional maintenance of the internal precision circuits and sensors may cause secondary damage.

When storing teaching devices, they should be placed in a dedicated protective box and kept in a ventilated and dry place to avoid mixing with corrosive chemicals.

Summary: The use of the 00-291-556 robot teaching pendant should focus on anti ｄｒｏｐ, anti short circuit, and anti misoperation protection, strictly follow the principle of manual low-speed debugging, pay attention to cable maintenance and battery maintenance in daily life, avoid risk behaviors such as sharp object scratches and live plugging, and ensure the sensitivity and service life of the teaching pendant, ensuring the safety of robot debugging and operation.

00-291-556机器人示教器 产品展示

产品视频

3.其他产品

IS215UCVFH2BB伺服控制器
GOP2控制操作触摸屏
07KR31 FPR36000227R1202-S可编程处理器单元

4.其他英文产品

BENTLY 2880065-01 Monitor module
GE 369B1860G0028 Electrical module
GE 44A751101-G01 Electrical module

The content is from Ruichang Mingsheng Automation Equipment Co., LTD

Contact: +86 15270269218