1.产 品 资 料 介 绍：
- 安装 FANUC A06B-0153-B075 需选用刚性法兰支架，固定扭矩 150-180N・cm，确保 3000rpm 高速运行无振动移位。
- 接线前确认供电电压与 A06B-0153-B075 额定 168VAC（200Hz）匹配，防止超压损坏 4.8kW 功率级绕组。
- 该型号适配 FANUC A64 系列驱动器，需通过系统参数匹配硬件 ID，保障转矩与转速控制精度。
- 编码器信号线采用双绞屏蔽电缆单独布线，接头锁紧到位，减少电磁干扰保障信号传输稳定。
- 定期用干燥抹布清洁 A06B-0153-B075 外壳，IP65 防护需重点防范粉尘与低压喷射水侵入，避免液体接触损坏部件。
- 运行环境温度控制在 - 10℃至 + 40℃，超温需按 1.5%/℃降容使用，避免 30Nm 转矩输出时过热。
- 耦合件安装采用热套或专用夹具，利用直轴键槽定位，禁止敲打轴端，保护精密轴承与轴系结构。
- 接线端子紧固按 1.2-1.5N・m 扭矩操作，多股导线压接铜鼻子，防止松动导致供电不稳。
- 每 12 个月检测绕组绝缘电阻≥10MΩ，同时清理散热鳍片灰尘，保障高功率运行时散热效率。
- 闲置超 6 个月重启前，手动转动轴体检查灵活性，空载预热 30 分钟后，逐步加载至 30Nm 额定转矩。
A06B-0153-B075伺服电机 英文资料：
Installation of FANUC A06B-0153-B075 requires the use of a rigid flange bracket with a fixed torque of 150-180N · cm to ensure vibration free displacement during high-speed operation at 3000rpm.
Before wiring, confirm that the power supply voltage matches the rated 168VAC (200Hz) of A06B-0153-B075 to prevent overvoltage damage to the 4.8kW power level winding.
This model is compatible with FANUC A64 series drivers and requires hardware ID matching through system parameters to ensure torque and speed control accuracy.
The encoder signal line is separately wired using twisted pair shielded cables, with the joints locked in place to reduce electromagnetic interference and ensure stable signal transmission.
Regularly clean the A06B-0153-B075 casing with a dry cloth. The IP65 protection should focus on preventing dust and low-pressure spray water from entering, and avoiding damage to components caused by liquid contact.
The operating environment temperature should be controlled between -10 ℃ and+40 ℃. If the temperature exceeds the limit, the capacity should be reduced by 1.5%/℃ to avoid overheating during 30Nm torque output.
The installation of coupling components adopts hot sleeves or specialized fixtures, and uses straight shaft keyway positioning. It is forbidden to knock the shaft end to protect the precision bearings and shaft structure.
Tighten the wiring terminals with a torque of 1.2-1.5N · m, and crimp multiple wires with copper noses to prevent loosening and unstable power supply.
Every 12 months, check the insulation resistance of the winding to be ≥ 10M Ω, and clean the dust on the heat dissipation fins to ensure the heat dissipation efficiency during high-power operation.
Before restarting after being idle for more than 6 months, manually rotate the shaft to check its flexibility. After preheating for 30 minutes without load, gradually load it to the rated torque of 30Nm.
Summary: The stable operation core of FANUC A06B-0153-B075 servo motor lies in standardized installation, voltage matching, IP65 protection maintenance, and load adaptation. Relying on the characteristics of 4.8kW high power, 30Nm high torque, and high-speed precision control, it is suitable for automation scenarios such as small and medium-sized machine tools. With compliant operation, it can fully leverage its industrial grade reliability and positioning accuracy advantages.
A06B-0153-B075伺服电机 产品展示
产品视频
3.其他产品
Foxboro FBM219 P0916RH输入/输出模块
Foxboro P0904AKI/O接口模块
WOODWARD 8444-1067PLC模块
4.其他英文产品
UFC760BE141 3BHE004573R0141 Thermocouple module
UFC760BE41 3BHE004573R0041 pulse output card
ABB UFC760BE42 3BHE004573R0042 pulse output card
| 710-774063-001 | 8020-SCP-332 | X-DI 32 04 |
| 710-679375-00 | 8020-SCP-323 | X-DI 32 03 |
| 710-678545-00 | 8020-SCP-322 | X-DI 32 02 |
| 710-678525-001 | 8020-SCP-321 | X-DI 32 01 |
| 710-678272-0C1 | 8020-SCP-313 | X-DI 64 51 |
| 710-678272-001 | 8020-SCP-312 | X-DI 64 01 |
| 710-677928-00 | 8020-SCP-311 | X-COM 01 E |
| 710-664601-000 | 8020-SCP-122 | X-SB 01 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
