MDD093C-N-020- N2L-130GA00伺服电机
1.产 品 资 料 介 绍：
- 安装 Indramat MDD093C-N-020-N2L-130GA00 需选用 130mm 定心直径支架，固定扭矩 150-180N・cm，适配任意安装方位无振动移位。
- 接线前确认供电电压与 MDD093C-N-020-N2L-130GA00 额定规格匹配，避免波动损坏绕组及编码器内置电路。
- 该型号适配 Indramat 数字驱动器，编码器存储电机专属数据，需通过系统参数完成驱动匹配实现快速启动。
- 编码器信号线采用专用屏蔽电缆单独布线，右侧连接器锁紧到位，减少电磁干扰保障位置反馈精度。
- 定期用干燥抹布清洁 MDD093C-N-020-N2L-130GA00 外壳，IP65 防护需重点防范粉尘与低压喷射水，保护轴端密封结构。
- 运行环境温度控制在 0℃至 + 40℃，湿度≤85%（无凝露），避免腐蚀性气体接触，适配恶劣工业场景。
- 耦合件安装采用热套或专用夹具，利用光轴带密封设计定位，禁止敲打轴端，保护精密轴承与轴系。
- 接线端子紧固按 1.2-1.5N・m 扭矩操作，多股导线压接铜鼻子，符合 NEC/CEC 电气安全规范。
- 每 12 个月检测绕组绝缘电阻≥10MΩ，同时清理散热面灰尘，检查轴承润滑状态，避免异响故障。
- 闲置超 6 个月重启前，手动转动轴体检查灵活性，空载预热 30 分钟，逐步加载至额定转矩运行。
MDD093C-N-020- N2L-130GA00伺服电机 英文资料：
Installation of Indramat MDD093C-N-020-N2L-130GA00 requires the use of a 130mm centering diameter bracket with a fixed torque of 150-180N · cm, suitable for any installation orientation without vibration displacement.
Before wiring, confirm that the power supply voltage matches the rated specifications of MDD093C-N-020-N2L-130GA00 to avoid damage to the winding and encoder built-in circuit caused by fluctuations.
This model is compatible with Indramat digital drivers, and the encoder stores motor specific data. Drive matching needs to be completed through system parameters to achieve fast startup.
The encoder signal line is separately wired with a dedicated shielded cable, and the right connector is locked in place to reduce electromagnetic interference and ensure position feedback accuracy.
Regularly clean the MDD093C-N-020-N2L-130GA00 housing with a dry cloth, with a focus on preventing dust and low-pressure spray water, and protecting the shaft end sealing structure with IP65 protection.
The operating environment temperature is controlled between 0 ℃ and+40 ℃, with humidity ≤ 85% (no condensation), avoiding contact with corrosive gases and adapting to harsh industrial environments.
The installation of coupling components adopts hot sleeves or specialized fixtures, and uses optical axis sealing design for positioning. It is forbidden to knock the shaft end to protect the precision bearings and shaft system.
The terminal block should be tightened with a torque of 1.2-1.5N · m, and multi strand wires should be crimped with copper noses, in compliance with NEC/CEC electrical safety regulations.
Every 12 months, check the insulation resistance of the winding to be ≥ 10M Ω, clean the dust on the heat dissipation surface, check the lubrication status of the bearings, and avoid abnormal noise faults.
Before restarting after being idle for more than 6 months, manually rotate the shaft to check its flexibility, preheat it for 30 minutes without load, and gradually load it to the rated torque for operation.
Summary: The stable operation core of Indramat MDD093C-N-020-N2L-130GA00 servo motor lies in standardized installation, drive matching, IP65 protection maintenance, and bearing maintenance. Relying on the high-precision and wide adaptability characteristics of synchronous motors, it can adapt to automation scenarios such as machine tools and robots. With compliant operation, it can fully leverage its industrial grade reliability and fast start advantages.
MDD093C-N-020- N2L-130GA00伺服电机 产品展示
产品视频
3.其他产品
Foxboro FBM219 P0916RH输入/输出模块
Foxboro P0904AKI/O接口模块
WOODWARD 8444-1067PLC模块
4.其他英文产品
UFC760BE141 3BHE004573R0141 Thermocouple module
UFC760BE41 3BHE004573R0041 pulse output card
ABB UFC760BE42 3BHE004573R0042 pulse output card
| 710-774063-001 | 8020-SCP-332 | X-DI 32 04 |
| 710-679375-00 | 8020-SCP-323 | X-DI 32 03 |
| 710-678545-00 | 8020-SCP-322 | X-DI 32 02 |
| 710-678525-001 | 8020-SCP-321 | X-DI 32 01 |
| 710-678272-0C1 | 8020-SCP-313 | X-DI 64 51 |
| 710-678272-001 | 8020-SCP-312 | X-DI 64 01 |
| 710-677928-00 | 8020-SCP-311 | X-COM 01 E |
| 710-664601-000 | 8020-SCP-122 | X-SB 01 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
