MSK060C-0300-N N-S1-UP0-NNNN 伺服电机
1.产 品 资 料 介 绍：
- 安装时保证电机与负载同轴，减少径向力对 MSK060C-0300-NN-S1-UP0-NNNN 轴端的损伤。
- 搬运务必握住电机本体，切勿抓握编码器或电缆，避免损坏 MSK060C-0300-NN-S1-UP0-NNNN 的信号接口。
- MSK060C-0300-NN-S1-UP0-NNNN 支持位置、速度、转矩三闭环控制，适配精密机床等场景。
- 接线时需使用 VDE 认证工具，同时注意电缆弯曲半径，避免线路故障影响电机运行。
- 定期清洁编码器和散热鳍片，MSK060C-0300-NN-S1-UP0-NNNN 依赖自然散热保障性能。
- 虽具备 IP65 防护，仍需确保 MSK060C-0300-NN-S1-UP0-NNNN 运行环境温度在 0-40℃之间。
- 该型号为免维护轴承设计，无需额外添加润滑脂，避免擅自拆卸影响密封。
- 运行时若出现异常噪音，需立即停机，检查是否超出 MSK060C-0300-NN-S1-UP0-NNNN 的 24Nm 最大转矩限制。
- 拆卸耦合部件时禁止敲打轴端，MSK060C-0300-NN-S1-UP0-NNNN 轴端含 DIN 标准键槽需重点保护。
- 定期检查接线端子与保护导体连接，确保 MSK060C-0300-NN-S1-UP0-NNNN 接地牢固。
- 避免施加超过规定的轴向负载，防止损伤电机轴承和内部传动结构。
- 配套电缆若出现破损需立即更换，不可临时修补，避免影响电机绝缘性能。
- 调整 PID 参数时，可结合 MSK060C-0300-NN-S1-UP0-NNNN 的编码器分辨率优化定位精度。
- 连接外部设备时需加装油封，防止油污侵入电机内部造成部件腐蚀。
- 长期闲置后重启，需先检测绝缘性，确认无异常后再按额定转速逐步试运行。
MSK060C-0300-N N-S1-UP0-NNNN 伺服电机 英文资料：
Ensure that the motor is coaxial with the load during installation to reduce radial force damage to the MSK060C-0300-NN-S1-UP0-NNNN shaft end.
Be sure to hold the motor body during transportation, and do not grip the encoder or cable to avoid damaging the signal interface of MSK060C-0300-NN-S1-UP0-NNNN.
MSK060C-0300-NN-S1-UP0-NNNN supports three loop control of position, speed, and torque, and is suitable for precision machine tools and other scenarios.
When wiring, VDE certification tools should be used, and attention should be paid to the bending radius of the cable to avoid line faults affecting motor operation.
Regularly clean the encoder and heat dissipation fins, MSK060C-0300-NN-S1-UP0-NNNN relies on natural heat dissipation to ensure performance.
Although equipped with IP65 protection, it is still necessary to ensure that the operating environment temperature of MSK060C-0300-NN-S1-UP0-NNNN is between 0-40 ℃.
This model is designed with maintenance free bearings and does not require additional lubricating grease to avoid unauthorized disassembly and affecting the seal.
If there is abnormal noise during operation, stop the machine immediately and check if it exceeds the maximum torque limit of 24Nm for MSK060C-0300-NN-S1-UP0-NNNN.
When disassembling the coupling components, it is forbidden to strike the shaft end. The MSK060C-0300-NN-S1-UP0-NNNN shaft end with DIN standard keyway needs special protection.
Regularly check the connection between the wiring terminal and the protective conductor to ensure that MSK060C-0300-NN-S1-UP0-NNNN is firmly grounded.
Avoid applying axial loads exceeding the specified limits to prevent damage to the motor bearings and internal transmission structure.
If the supporting cable is damaged, it should be replaced immediately and cannot be repaired temporarily to avoid affecting the insulation performance of the motor.
When adjusting PID parameters, the positioning accuracy can be optimized by combining the encoder resolution of MSK060C-0300-NN-S1-UP0-NNNN.
When connecting external devices, it is necessary to install oil seals to prevent oil contamination from entering the interior of the motor and causing component corrosion.
After being idle for a long time and restarting, it is necessary to first test the insulation and confirm that there are no abnormalities before gradually running at the rated speed.
Summary: The stable operation of MSK060C-0300-NN-S1-UP0-NNNN servo motor needs to take into account both general specifications and exclusive characteristics, with a focus on protection level adaptation, encoder protection, load torque control, and compliance maintenance, fully leveraging its precision control and high reliability advantages to extend the service life of the entire machine.
MSK060C-0300-N N-S1-UP0-NNNN 伺服电机 产品展示
产品视频
3.其他产品
GE DS200PCCAG1ABB发电机保护系统模块
GE DS200SLCCG1AFG DS215SLCCG1AZZ01A发电机控制器模块
GE DS200SDCCG1AGD DS215SDCCG1AZZ01B发电机控制器模块
4.其他英文产品
BENTLY 3500/25 184684-01 Monitor module
PM510V16 3BSE008358R1 processor module
PM511V08 3BSE011180R1 processor module
| EP3640-1436-7-56BC-CU | 531X124MSDAGG1 | 330730-040-00-00 |
| EP3632-1435-7-56BC-CU | 531X124MSDADG1 | IC3600TPAE1B1C |
| EP3624-5269-7-56BC-CU | 531X124MSDAAG1 | 330710-000-060-10-02-00 |
| EP3624-2757-7-56BC-CU | 531X123PCHACG2 | 3500/45 176449-04 |
| EP3624-1434-7-56BC-CU | 531X123PCHACG1 | 136188-01 |
| EP3620-4460-7-56C-CU | 531X122PCNAMG1 | 330180-51-05 |
| EP3620-1954-7-56BC-CU | 531X122PCNALG2 | 330850-90-05 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
