1.产 品 资 料 介 绍：
- 安装 2EX100.50-1 需适配 B&R System 2010 机架，固定扭矩控制在 150-180N・cm，确保安装面平整无松动。
- 接线前确认输入电压合规（建议 24VDC±10%），避免过压损坏 2EX100.50-1 内部总线控制模块。
- 2EX100.50-1 支持 Modbus、Profinet 等主流通信协议，需与从站设备匹配协议版本，保障数据传输稳定。
- 信号电缆与动力电缆分开布线（间距≥20cm）并屏蔽接地，减少对 2EX100.50-1 的电磁干扰，符合 IEC 61131-2 EMC 标准。
- 定期清洁 2EX100.50-1 的接口触点，用干燥毛刷清除灰尘，防范接触不良或信号中断。
- 运行环境温度控制在 - 10℃至 + 60℃，湿度 20%-85%（无凝露），适配其工业级工作范围。
- 2EX100.50-1 参数配置后需通过专用软件备份，同时记录关键参数，防止误操作导致配置丢失。
- 拆卸模块时需先断开机架电源，等待指示灯完全熄灭后再操作，禁止带电插拔 2EX100.50-1 避免接口损坏。
- 扩展 I/O 模块时，2EX100.50-1 最多可适配 32 个扩展单元，支持数字量、模拟量等多种模块组合。
- 模拟量输入接线需注意信号极性，避免接反导致 2EX100.50-1 的 AD 转换模块损坏。
- 定期检查 2EX100.50-1 的散热情况，机架通风口需保持通畅，避免覆盖异物影响散热。
- 出现通信故障时，先检查 2EX100.50-1 的总线终端电阻（建议 120Ω）是否安装到位。
- 禁止用尖锐工具触碰 2EX100.50-1 的接线端子，防止损坏引脚或造成短路。
- 长期运行后，每 6 个月校验一次 2EX100.50-1 的通信延迟与数据传输精度，及时调整参数。
- 闲置超过 3 个月后重启，需先通电预热 30 分钟，再逐步加载负载，保护内部电容与电路。
2EX100.50-1 控制器模块 英文资料：
The installation of 2EX100.50-1 requires compatibility with the B&R System 2010 rack, with a fixed torque controlled between 150-180N · cm to ensure a flat and secure installation surface.
Before wiring, confirm that the input voltage is compliant (recommended 24VDC ± 10%) to avoid overvoltage damage to the 2EX100.50-1 internal bus control module.
2EX100.50-1 supports mainstream communication protocols such as Modbus and Profinet, and needs to match the protocol version with the slave device to ensure stable data transmission.
The signal cable and power cable are wired separately (with a spacing of ≥ 20cm) and shielded to reduce electromagnetic interference to 2EX100.50-1, in compliance with the IEC 61131-2 EMC standard.
Regularly clean the interface contacts of 2EX100.50-1, use a dry brush to remove dust, and prevent poor contact or signal interruption.
The operating environment temperature is controlled between -10 ℃ and+60 ℃, with a humidity of 20% -85% (no condensation), suitable for its industrial grade working range.
After configuring the 2EX100.50-1 parameters, they need to be backed up through dedicated software, and key parameters should be recorded to prevent configuration loss caused by misoperation.
When disassembling the module, it is necessary to first disconnect the power supply of the power rack and wait for the indicator light to completely turn off before operating. It is forbidden to plug and unplug 2EX100.50-1 with power on to avoid interface damage.
When expanding I/O modules, 2EX100.50-1 can accommodate up to 32 expansion units and supports various module combinations such as digital and analog.
Attention should be paid to signal polarity in analog input wiring to avoid reverse connection, which may cause damage to the AD conversion module of 2EX100.50-1.
Regularly check the heat dissipation of 2EX100.50-1, and keep the rack ventilation openings unobstructed to avoid covering foreign objects that may affect heat dissipation.
When a communication failure occurs, first check whether the bus terminal resistance (recommended 120 Ω) of 2EX100.50-1 is installed properly.
Do not touch the 2EX100.50-1 terminal block with sharp tools to prevent damage to the pins or short circuits.
After long-term operation, verify the communication delay and data transmission accuracy of 2EX100.50-1 every 6 months and adjust the parameters in a timely manner.
After being idle for more than 3 months and restarting, it is necessary to first power on and preheat for 30 minutes before gradually loading the load to protect the internal capacitors and circuits.
Summary: The key to the stable operation of the 2EX100.50-1 controller module lies in standardized installation, protocol matching, EMC protection, environmental adaptation, and regular maintenance. Its support for multi protocol communication and flexible I/O expansion, combined with compliant operation, can fully leverage the high reliability and adaptability advantages of bus control, effectively ensuring the continuous and stable operation of industrial automation systems.
2EX100.50-1 控制器模块 产品展示
产品视频
3.其他产品
Motorola MVME162-213VME总线计算机板卡
ABB 81EU01E-E GJR2391500R1210 GJR2391511R42控制器模块
ABB SR469-P5-HI-A20-E 数字继电器保护装置
4.其他英文产品
HIMA F8652X controller module
Honeywell SPS5710 51199929-100 Channel interface module
Honeywell SPS5710-2-LF 51198685-100 module
| 850-EP5NNG5HNNALNGMSFB3ACNAN | AMAT 0100-20009 | 46088611 |
| 850-EP5NNG5HNNALFGAPCASENNBN | AMAT 0100-00438 | MPCBL0001F04 |
| 850-EP5NNG5HNNALAGASFCSENWBN2 | AMAT 0100-98072 | SN32HMYW-LNK-NS-00 |
| 850-EP5NNG5HNNALAGAPFBSENNBN | AMAT 0100-91087 | 48797303 |
| 850-EP5NNG5HNNAANMASFB1ECNAN | AMAT 0100-94078 | 135837-008 |
| 850-EP5NNG5HNNAANGMPHB3ACNBN | AMAT 0100-09110 | 48011401 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
