1.产 品 资 料 介 绍：
- 安装 Lenze MDFKABA090-22 时，电机与负载同轴度需≤0.1mm，降低振动对高动态响应性能的影响。
- 搬运需紧握电机本体，严禁抓握 MDFKABA090-22 的编码器端或接线盒，避免损坏精密信号部件。
- Lenze MDFKABA090-22 支持位置 / 速度 / 转矩三模式控制，切换需通过 9300 系列伺服控制器配置。
- 接线时编码器信号线与动力电缆分开布线并做好屏蔽接地，减少对 MDFKABA090-22 信号传输的干扰。
- 定期清洁 Lenze MDFKABA090-22 的编码器窗口，IP54 防护等级需重点防范灰尘与飞溅液体侵入。
- 运行环境温度控制在 - 10℃至 + 40℃，适配 MDFKABA090-22 工业级热设计，40℃以上需降容使用。
- 电机轴承为密封免维护设计，无需额外加注润滑脂，避免拆卸破坏 Lenze MDFKABA090-22 的防护结构。
- 避免对 MDFKABA090-22 施加超额定值的轴向负载，保护轴系与键槽结构（适配 8mm 标准键）。
- 接线端子紧固扭矩控制在 120-150N・cm，防止松动导致 Lenze MDFKABA090-22 供电不稳。
- 配套电缆弯曲半径不小于电缆直径的 10 倍，接线盒密封面需保持清洁，避免影响防护效果。
- 运行中若 MDFKABA090-22 外壳温度超过 85℃，需停机检查负载与散热情况，避免绕组过热。
- 拆卸耦合部件需使用专用拉拔器，禁止敲打轴端，保护 Lenze MDFKABA090-22 的轴系精度。
- 定期校验编码器接线完整性，确保与 MDFKABA090-22 的高精度反馈功能及控制器匹配。
- 电机表面需保持清洁，用压缩空气清除灰尘，保障散热筋的散热效率，提升运行稳定性。
- 长期闲置后重启，需先检测绕组绝缘电阻≥5MΩ，确认无凝露后再按额定转速逐步试运行。
When installing Lenze MDFKABA090-22, the coaxiality between the motor and the load should be ≤ 0.1mm to reduce the impact of vibration on high dynamic response performance.
Handle the motor body tightly during transportation, and it is strictly prohibited to grip the encoder end or junction box of MDFKABA090-22 to avoid damaging precision signal components.
Lenze MDFKABA090-22 supports position/speed/torque three mode control, and switching needs to be configured through 9300 series servo controller.
When wiring, separate the encoder signal line from the power cable and ensure proper shielding and grounding to reduce interference with MDFKABA090-22 signal transmission.
Regularly clean the encoder window of Lenze MDFKABA090-22, with an IP54 protection level that focuses on preventing dust and splashing liquids from entering.
The operating environment temperature is controlled between -10 ℃ and+40 ℃, suitable for MDFKABA090-22 industrial grade thermal design. If the temperature is above 40 ℃, it needs to be used with reduced capacity.
The motor bearings are designed to be sealed and maintenance free, without the need for additional lubricating grease, to avoid disassembly and damage to the protective structure of Lenze MDFKABA090-22.
Avoid applying axial loads beyond the rated value to MDFKABA090-22, protect the shaft system and keyway structure (compatible with 8mm standard keys).
The tightening torque of the terminal block should be controlled between 120-150N · cm to prevent looseness from causing unstable power supply to Lenze MDFKABA090-22.
The bending radius of the supporting cable shall not be less than 10 times the diameter of the cable, and the sealing surface of the junction box shall be kept clean to avoid affecting the protective effect.
If the shell temperature of MDFKABA090-22 exceeds 85 ℃ during operation, it is necessary to shut down and check the load and heat dissipation to avoid overheating of the winding.
Disassembling the coupling components requires the use of a specialized puller, and it is forbidden to strike the shaft end to protect the axis accuracy of Lenze MDFKABA090-22.
Regularly verify the integrity of the encoder wiring to ensure compatibility with the high-precision feedback function and controller of MDFKABA090-22.
The surface of the motor needs to be kept clean, and dust should be removed with compressed air to ensure the heat dissipation efficiency of the cooling ribs and improve operational stability.
After being idle for a long time and restarting, it is necessary to first check that the insulation resistance of the winding is ≥ 5M Ω, confirm that there is no condensation, and then gradually test run at the rated speed.
Summary: The stable operation core of Lenze MDFKABA090-22 servo motor lies in standardized installation, precise protection, and load adaptation, with a focus on coaxiality control, IP54 protection maintenance, encoder signal protection, and environmental temperature control. It fully utilizes its advantages of high power density, low moment of inertia, and industrial reliability. Paired with the 9300 series controller, it can maximize the overall operating efficiency and service life of the equipment.
产品视频
3.其他产品
ABB XVC517AE10 3BHB004744R0010控制器模块
ABB PCD1.M120PLC模块
A-B 1756-CNBR通信模块
4.其他英文产品
CI570 3BSE001440R1 MasterFieldbus Controller
HIMA F8628X controller
HIMA F8652X controller module
| 92081-02-1 | CACR-SR05AB1ERY3-V | 26390603-A DSTK150 ABB |
| 92-005422-0x | CACR-PR30BC3CSY166E | PFCL301E |
| 90785-6-1 | 6DD1681-0DJ1 | 26390582-AY DSTK126 ABB |
| 90773-01-1 | CACR-SR30SZ1SDY230 | ABB UAC389AE02 HIEE300888R0002 |
| 8V1090.00-2 | CACR-SR-10SZ1SF | PFEA 113-65.4PXV |
| -8SL11 | CACR-HR10BABY5 | 26390603-BS DSTK181 ABB |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
