1.产 品 资 料 介 绍：
- 安装 Kollmorgen AKM62K-ANCNDA0 时，电机与负载同轴度需≤0.1mm，降低运行振动与齿槽效应影响。
- 搬运需紧握电机本体，严禁抓握 AKM62K-ANCNDA0 的编码器端或连接器，避免损坏精密部件。
- Kollmorgen AKM62K-ANCNDA0 支持位置 / 速度 / 转矩三模式控制，切换需通过 AKD 系列驱动器配置。
- 接线时编码器信号线与动力电缆分开布线，减少电磁干扰，保障 AKM62K-ANCNDA0 信号传输稳定。
- 定期清洁 Kollmorgen AKM62K-ANCNDA0 的编码器窗口，IP40 标准防护型号需重点防灰尘侵入。
- 运行环境温度控制在 - 20℃至 + 40℃，适配 AKM62K-ANCNDA0 F 级绝缘（155℃）的热设计要求。
- 电机轴承为免维护密封设计，无需额外加注润滑脂，避免拆卸破坏防护密封件。
- 避免对 Kollmorgen AKM62K-ANCNDA0 施加超额定值的轴向负载，保护轴系与轴承使用寿命。
- 接线端子紧固扭矩控制在 120-150N・cm，防止松动导致 AKM62K-ANCNDA0 供电不稳。
- 配套电缆弯曲半径不小于电缆直径的 10 倍，IP67 防水型号需避免电缆接头浸水。
- 运行中若 Kollmorgen AKM62K-ANCNDA0 外壳温度超过 85℃，需停机检查负载与散热情况。
- 拆卸耦合部件需使用专用拉拔器，禁止敲打轴端，保护 AKM62K-ANCNDA0 的键槽结构。
- 定期校验编码器接线完整性，确保与 AKM62K-ANCNDA0 的高精度反馈功能匹配。
- 电机表面需保持清洁，用压缩空气清除灰尘，保障 F 级绝缘绕组的散热效率。
- 长期闲置后重启，需先检测绕组绝缘电阻≥5MΩ，再按额定转速逐步试运行。
AKM62K-ANCNDA0伺服电机 英文资料：
When installing Kollmorgen AKM62K-ANCNDA0, the coaxiality between the motor and the load should be ≤ 0.1mm to reduce the impact of operating vibration and cogging effect.
Handle the motor body tightly during transportation, and it is strictly prohibited to grip the encoder end or connector of AKM62K-ANCNDA0 to avoid damaging precision components.
Kollmorgen AKM62K-ANCNDA0 supports position/speed/torque three mode control, and the switch needs to be configured through AKD series drives.
When wiring, separate the encoder signal line from the power cable to reduce electromagnetic interference and ensure stable AKM62K-ANCNDA0 signal transmission.
Regularly clean the encoder window of Kollmorgen AKM62K-ANCNDA0, with a focus on preventing dust intrusion for IP40 standard protection models.
The operating environment temperature is controlled between -20 ℃ and+40 ℃, suitable for the thermal design requirements of AKM62K-ANCNDA0 F-class insulation (155 ℃).
The motor bearings are designed with maintenance free sealing and do not require additional lubrication to avoid disassembly and damage to the protective seals.
Avoid applying excessive axial loads to Kollmorgen AKM62K-ANCNDA0 to protect the service life of the shaft system and bearings.
The tightening torque of the terminal block should be controlled between 120-150N · cm to prevent looseness from causing unstable power supply to AKM62K-ANCNDA0.
The bending radius of the supporting cable shall not be less than 10 times the diameter of the cable, and the IP67 waterproof model shall prevent the cable joint from being immersed in water.
If the shell temperature of Kollmorgen AKM62K-ANCNDA0 exceeds 85 ℃ during operation, the machine needs to be stopped to check the load and heat dissipation.
Disassembling the coupling components requires the use of a specialized puller, and it is forbidden to strike the shaft end to protect the keyway structure of AKM62K-ANCNDA0.
Regularly verify the integrity of the encoder wiring to ensure compatibility with the high-precision feedback function of AKM62K-ANCNDA0.
The surface of the motor needs to be kept clean, and dust should be removed with compressed air to ensure the heat dissipation efficiency of the F-class insulation winding.
After being idle for a long time and restarting, it is necessary to first check that the insulation resistance of the winding is ≥ 5M Ω, and then gradually test run it at the rated speed.
Summary: The stable operation core of Kollmorgen AKM62K-ANCNDA0 servo motor lies in precise installation, standardized protection, and environmental adaptation, with a focus on coaxiality control, encoder protection, insulation heat dissipation, and load matching. It fully utilizes its advantages of low cogging torque, high power density, and industrial reliability to extend the overall service life of the equipment.
AKM62K-ANCNDA0伺服电机 产品展示
产品视频
3.其他产品
ABB XVC517AE10 3BHB004744R0010控制器模块
ABB PCD1.M120PLC模块
A-B 1756-CNBR通信模块
4.其他英文产品
CI570 3BSE001440R1 MasterFieldbus Controller
HIMA F8628X controller
HIMA F8652X controller module
| ALSTOM V4555724-0100 | AMAT 0100-76088 | 3500/22 146031-01 |
| AGL 400 | AMAT 0100-01714 | CE945GM2A-T25 |
| AGC-4 | AMAT 0100-38018 | GKWE001450R0009 XT382B-R9 |
| AGC 200 | AMAT 0100-00021 | HESG223044R0001 PT8153B-E |
| AGC 150 | AMAT 0100-00134 | NKAS01-10 |
| 989E502-G01 | AMAT 0100-00044 | 61-0532-34 |
| 989E500-G01 | AMAT 0100-20350 | RMS420-C610-03 |
| 989E186-G01 | AMAT 0010-86037 | IMSEM11 |
| 92661-02-1 | AMAT 0100-09115 | PFEA 113-65 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
