1.产 品 资 料 介 绍：
- 安装 Jetter JL4-0530-48-3R 时需保证电机与负载同轴度≤0.1mm，减少运行振动。
- 搬运需握住电机本体，严禁抓握 Jetter JL4-0530-48-3R 的编码器端或电缆接头。
- Jetter JL4-0530-48-3R 支持位置 / 速度 / 转矩三模式控制，切换需通过驱动器参数配置。
- 接线时编码器信号线需与动力电缆分开布线，避免干扰 JL4-0530-48-3R 信号传输。
- 定期清洁 Jetter JL4-0530-48-3R 的编码器窗口，防止灰尘影响定位精度。
- 运行环境温度控制在 - 10℃至 + 55℃，适配 Jetter JL4-0530-48-3R 工业级工作范围。
- 电机轴承为免维护设计，无需额外加注润滑脂，避免擅自拆卸破坏密封。
- 避免对 Jetter JL4-0530-48-3R 施加超过额定值的轴向负载，保护轴系结构。
- 接线端子紧固扭矩控制在 120-150N・cm，防止松动导致 JL4-0530-48-3R 供电不稳。
- 配套电缆弯曲半径不小于电缆直径的 10 倍，避免内部导线断裂。
- 运行中若 Jetter JL4-0530-48-3R 外壳温度超过 80℃，需立即停机检查负载。
- 拆卸耦合部件时需使用专用拉拔器，禁止直接敲打电机轴端。
- 定期检查编码器接线完整性，确保与 Jetter JL4-0530-48-3R 的信号反馈匹配。
- 电机表面需保持清洁，用压缩空气清除灰尘，保障自然散热效率。
- 长期闲置后重启，需先检测绕组绝缘电阻≥5MΩ，再低速试运行。
Jetter JL4-0530-48-3R伺服电机 英文资料：
When installing Jetter JL4-0530-48-3R, it is necessary to ensure that the coaxiality between the motor and the load is ≤ 0.1mm to reduce operational vibration.
Handle the motor body during transportation, and it is strictly prohibited to grip the encoder end or cable joint of Jetter JL4-0530-48-3R.
Jetter JL4-0530-48-3R supports position/speed/torque three mode control, and switching needs to be configured through driver parameters.
When wiring, the encoder signal line should be separated from the power cable to avoid interference with the JL4-0530-48-3R signal transmission.
Regularly clean the encoder window of Jetter JL4-0530-48-3R to prevent dust from affecting positioning accuracy.
The operating environment temperature is controlled between -10 ℃ and+55 ℃, suitable for the industrial working range of Jetter JL4-0530-48-3R.
The motor bearings are designed to be maintenance free and do not require additional lubrication to prevent unauthorized disassembly and damage to the seal.
Avoid applying axial loads exceeding the rated value to the Jetter JL4-0530-48-3R to protect the shaft system structure.
The tightening torque of the terminal block should be controlled between 120-150N · cm to prevent looseness from causing unstable power supply to JL4-0530-48-3R.
The bending radius of the supporting cable should not be less than 10 times the diameter of the cable to avoid internal wire breakage.
If the shell temperature of Jetter JL4-0530-48-3R exceeds 80 ℃ during operation, the machine should be stopped immediately to check the load.
When disassembling the coupling components, a specialized puller should be used and direct tapping of the motor shaft end is prohibited.
Regularly check the integrity of the encoder wiring to ensure that it matches the signal feedback of Jetter JL4-0530-48-3R.
The surface of the motor needs to be kept clean, and dust should be removed with compressed air to ensure natural heat dissipation efficiency.
After being idle for a long time and restarting, it is necessary to first check that the insulation resistance of the winding is ≥ 5M Ω, and then conduct low-speed trial operation.
Summary: The stable operation core of Jetter JL4-0530-48-3R servo motor lies in precise installation, standardized protection, and regular maintenance, with a focus on coaxiality control, encoder protection, load matching, and environmental adaptation. It fully leverages its high-precision positioning and industrial grade reliability advantages to extend equipment service life.
Jetter JL4-0530-48-3R伺服电机 产品展示
产品视频
3.其他产品
ABB 83SR06B-E GJR2395400R1210数字输入模块
Cognex MC-PDIY22 80363972-150视觉传感器
ABB XVC517AE10 3BHB004744R0010控制器模块
4.其他英文产品
UAD155A0111 3BHE029110R0111 Excitation control card
ALSTOM 43297029 Distributed control card
ALSTOM BGTR8HE 24491276A1004 framework
| BA3628-5822-9-56BC | HG92S94A6 | 57160001-AAA DSDI110A ABB |
| BA3628-1331-56B | HA110D6 | DSTC404 ABB |
| BA3624-7045-56C | SS9MS-11A1A0A | 5736 045-N DSMD113 ABB |
| BA3624-7024-9-56BC | HA42A6 | IMASO11 |
| BA3624-7005-9-56BC | SL2C-38L | EPC-161316AE |
| BA3624-5558-56B | SL4-120-RBKK-CR | 48964402-D, |
| BA3618-7009-9-56BC | SB4-J254 | ICS TRIPLEX TC-801-02- .4M5 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
