1.产 品 资 料 介 绍：
- 三菱 MELSEC A 系列专属 PROFIBUS-DP 从站通信模块，核心作用是搭建 PLC 与工业设备的标准化通信桥梁，实现跨设备数据交互
- 品牌归属：三菱电机（Mitsubishi Electric），产品状态：已停产（OEM 停产后，第三方供应商提供测试合格的二手产品，部分支持 1 年质保 + 30 天退换服务）
- 适配场景：专为工业分布式控制设计，可融入三菱三层网络架构（信息层、控制层、设备层），与 Q 系列 PLC 搭配兼容性最优
- 协议与接口：严格遵循 PROFIBUS-DP 协议，EIA-RS485 电气接口，数据编码采用 NRZ（不归零码）格式
- 传输规格：速度覆盖 9.6kbps-12Mbps，对应传输距离 100m-1200m（低速时最远），每段支持 32 个模块，单个主站可管理 60 个从站单元
- 布线要求：需使用屏蔽双绞线（2 线制），避免与主电路 / 电源线近距离并行（建议间距≥100mm），减少电磁干扰
- 扩展能力：支持最多 3 台增幅器级联，可将最大传输距离扩展 4 倍（如 1200m 扩展至 4800m）
- 供电参数：DC5V 供电，内耗电量 0.36A，需依赖 PLC 系统电源供电，无独立电源接口
- I/O 细节：32 点智能 I/O 分配（输入 16 点 / 输出 16 点），输入电压 DC12/24V，输入电流 4/10mA，应答时间 10ms；输出为晶体管漏型，DC24V 输出，单点点电流 0.1A，8 个端子为一组公共端（正极公用）
- 连接方式：40 针连接器接口，搭配 20 端子台，插拔式模块化设计，便于基板插槽安装与维护
- 尺寸重量：130mm（高）×34.5mm（宽）×93.6mm（深），重量 0.18kg（运输重量约 2.27kg / 台）
- 工作环境：0～55℃使用温度，-20～85℃保存温度，相对湿度≤90%（无结露），海拔 1000m 以下
- 防护特性：具备基础电磁干扰防护，依赖屏蔽线缆进一步提升抗干扰能力
HR115C6-88S伺服电机 英文资料：
1、 Core positioning
Mitsubishi MELSEC A-series exclusive PROFIBUS-DP slave communication module, the core function is to build a standardized communication bridge between PLC and industrial equipment, realizing cross device data exchange
Brand ownership: Mitsubishi Electric, product status: discontinued (after OEM discontinuation, third-party suppliers provide tested and qualified second-hand products, some support 1-year warranty+30 day return and exchange service)
Adaptation scenario: Designed specifically for industrial distributed control, it can integrate into Mitsubishi's three-layer network architecture (information layer, control layer, equipment layer) and has the best compatibility with Q series PLCs
2、 Key parameters (additional details)
1. Communication performance
Protocol and Interface: Strictly follow the PROFIBUS-DP protocol, EIA-RS485 electrical interface, and use NRZ (Non Return to Zero) format for data encoding
Transmission specifications: speed coverage of 9.6kbps-12Mbps, corresponding transmission distance of 100m-1200m (farthest at low speed), each segment supports 32 modules, and a single master station can manage 60 slave units
Wiring requirements: Shielded twisted pair (2-wire system) should be used to avoid parallel connection with the main circuit/power line at a close distance (recommended spacing ≥ 100mm) and reduce electromagnetic interference
Scalability: Supports up to 3 amplifiers cascaded, and can extend the maximum transmission distance by 4 times (such as 1200m to 4800m)
2. Power supply and I/O characteristics
Power supply parameters: DC5V power supply, internal power consumption of 0.36A, dependent on PLC system power supply, no independent power interface
I/O details: 32 point intelligent I/O allocation (input 16 points/output 16 points), input voltage DC12/24V, input current 4/10mA, response time 10ms; output is transistor leakage type, DC24V output, single point current 0.1A, 8 terminals are a group of common terminals (positive common)
Connection method: 40 pin connector interface, matched with 20 terminal block, plug-in modular design, easy to install and maintain substrate slots
3. Physical and Environmental Specifications
Size and weight: 130mm (height) x 34.5mm (width) x 93.6mm (depth), weight 0.18kg (transportation weight approximately 2.27kg/unit)
Working environment: operating temperature of 0-55 ℃, storage temperature of -20~85 ℃, relative humidity ≤ 90% (no condensation), altitude below 1000m
Protection features: equipped with basic electromagnetic interference protection, relying on shielded cables to further enhance anti-interference ability
HR115C6-88S伺服电机 产品展示
产品视频
3.其他产品
ABB LSP086388-001控制模块
B&R 7AT664.70控制器模块
B&R 7AO352.70输出模块
4.其他英文产品
DEIF PCM4.4 ship controller
YASKAWA JAPMC-IQ2303 Switch voltage module
BENTLY 135489-01 Monitor card
| SC723A001 |  6SC6100-0NA21 | 6ES5-456-7LA11 |
| SC723 | SC452-047-05 | SCE905AN-001-01 |
| SC722B-001 | SC723B00101 | SCE904AN-001-01 |
| SC722A-001-PM72036 | SC453-002-15 | SCE905-001-01 A |
| SC722A-001-PM72012 | SC722A001 | SCE904AN-002-01 |
| SC722A-001-PM72005 | OS63D12 fuse switch | SCE952NN-504-01 |
The content is from Ruichang Mingsheng Automation Equipment Co., LTD
Contact: +86 15270269218
